Do you need to replace your toilet? This guide can help you to replace your old toilet. You can install a toilet DIY. However, the steps below will help you get your toilet running in no time.
There are many reasons to get a new toilet
Several reasons can lead to the need for a new toilet. It is usually easy to identify signs that your current toilet needs replacing. These are:
- Frequent clogging
- Frequent repairs
- Cracking, scratching or rusting
- General update
- Bathroom remodelling
- Water and energy conservation
How a toilet works
A toilet is simply a tank and bowl. The tank, also known as the cistern, is located above the bowl. It contains water that recharges each flush. The bowl holds water and connects to the sewage drain for water disposal and waste. When the toilet flushes, water from its cistern is forced into the bowl and the contents are forced through the "S bend" to the sewer pipe.
How long does it take for a toilet to be installed?
The average time it takes to install a toilet is between 1-4 hours, depending on what type of toilet you're fitting and how experienced you are in doing the job. You will then need to install your toilet seat. This may take a few minutes depending on how big the toilet is.
How to prepare for fitting your toilet
Before installing your new toilet, there are some things you need to do. These are:
Ensure you have the correct equipment
These are the most important tools that you will need to do the job.
- Screwdriver
- Wrenches
- Rubber gloves
- Silicone
- Adjustable pliers
You may also need the following equipment if you are installing a toilet system from scratch or connecting a cistern tank to the bowl or pan.
- Hammer
- Drill
- Bucket
- Pipe wrench
- Tape measure
- Box spanner
- Spirit level
- Pipe Cutter or Hacksaw
- Pencil
- Towel
- Flexible hose
How to get rid of an old toilet
Turn off your water supply - You must ensure there is no water left in the toilet's bowl or cistern tank. The isolation valve will shut off the water supply to the toilet. After that, flush the toilet until there is no more water. There may be some water left in the pan or cistern. You can get rid of it by using an old towel. The towel should be pushed down and then rubbed over a bucket.
Disconnect your water pipe from the toilet's cistern - The water pipe connects to the toilet system's water cistern and filters water into it when needed. To prevent water from leaking out, disconnect it with a wrench.
Disassemble the fixtures - This step will require you to take out the parts that attach your toilet to the ground. To help remove silicone, carefully unscrew the washers and nuts.
Disconnect the soil pipe - There should be an outlet in the back of the toilet that connects with the soil or waste pipes. Carefully and gently remove the toilet from the pipe.
Cover the soil pipe - Use a cloth or bag to cover the soil pipe and stop any potentially dangerous and unpleasant gases from getting into the room.
These preparatory steps can also help you identify any other elements that may need to be replaced, aside from the toilet.
How to get rid of an old toilet
Your old toilet should be taken to the local household waste recycling centre (also called "the tip") To make sure they accept your item, you can search online for your nearest tip or visit your local council's site.
Before moving the toilet to the recycling facility, make sure it is dry and clean.
How to install a toilet
The main event is now - installing your toilet.
Important: Before you start, we recommend that you read the instructions from your manufacturer.
This is our step-by-step guide for fitting your new toilet.
1. Install the flush mechanism. Attach the rubber sealing rings. Be careful not to tighten any fittings.
2. Place the large rubber gasket in the flush opening of the pan.
3. Use the supplied metal washers to secure the long bolts in the holes of the cistern.
4. Place the cistern on the toilet pan by lifting it and making sure that the bolts are in the right places.
5. Attach washers to the bolts, and tighten the wing nuts.
6. Before you place the toilet, make sure to check for cables or pipes below the fixing points. Next, insert the pan outlet into an adapter that is attached to the soil pipe. Next, drill pilot holes in the floor to align with the fixing points. Be careful not to hit any cables or pipes! ).
7. Use plastic protective inserts to push the pan's base through the holes. Then, screw the retaining screws into the floor. If the cistern has fixing holes at the back, then you will need to attach it to a wall by drilling and plugging. Tip: Before tightening the nuts, make sure you add rubber washers.
8. You will need to connect the supply line using a push-fit connector for cold water feed.
9. Follow the manufacturer's instructions to attach the hinge assembly onto the toilet seat.
10. Connect the seat to the pan using screws - make sure you secure it through the holes in the back. Adjust it until it is in the correct position.
Aftercare
- Toilets can last for up to 50 years, according to some. There are many ways you can prolong the life of your toilet throne. These are:
- It is important to maintain it properly. This means using non-abrasive cleaners to prevent damage. You can also use plastic bristles rather than wire brushes. It's important to use it correctly - we are sure you can do it! You shouldn't place your back against the tank/cistern, and you should not stand on the lid or the seat - even though it may be necessary to reach something.
- When closing the toilet, be careful not to lower the lid too much.
- Do not treat your toilet as a trash can.
- As soon as possible, address any problems with your toilet.
To avoid lasting damage, you should immediately correct any problems.
No comments:
Post a Comment